0o -.......Forum 361dodesign.com.......- o0
Hãy tham gia diễn đàn 361dodesign ngay hôm nay và hãy đăng ký thành viên để có thể xem hiển thị hết diễn đàn + links download + và chia sẻ kinh nghiệm..v..v..!!!!!!!!!!!!!!!!!!!!!!
Chúc các bạn một ngày vui vẻ..

0o -.......Forum 361dodesign.com.......- o0

Dịch vụ Thiết kế - In ấn - In Offset - Thế giới Thiết kế - Download phần mềm - Download Vector Free - Hỗ trợ Forum
 
Trang ChínhCalendarGalleryTrợ giúpTìm kiếmThành viênNhómĐăng kýĐăng Nhập

Share | 
 

  TYPES OF PORTAL FRAMES (.dwg) (WORKING DRAWINGS)

Go down 
Tác giảThông điệp
nguyentienhai12h2

avatar

Tổng số bài gửi : 51
Điểm tích lũy : 2627
Thích : 0
Tham gia : 27/02/2012

Bài gửiTiêu đề: TYPES OF PORTAL FRAMES (.dwg) (WORKING DRAWINGS)    Mon Jun 17, 2013 2:46 pm

[You must be registered and logged in to see this image.]

[hide]
Portal frame construction is a method of building and designing structures, primarily using steel or steel-reinforced precast concrete although they can also be constructed using laminated timber such as glulam. The connections between the columns and the rafters are designed to be moment-resistant, i.e. they can carry bending forces.
Because of these very strong and rigid joints some of the bending moment in the rafters is transferred to the columns. This means that the size of the rafters can be reduced or the span can be increased for the same size rafters. This makes portal frames a very efficient construction technique to use for wide span buildings.
Portal frame construction is therefore typically seen in warehouses, barns and other places where large, open spaces are required at low cost and a pitched roof is acceptable.
Generally portal frames are used for single story buildings but they can be used for low rise buildings with several floors where they can be economic if the floors do not span right across the building (in these circumstances a skeleton frame, with internal columns, would be a more economic choice). A typical configuration might be where there is office space built against one wall of a warehouse.
Portal frames can be clad with all sorts of material but the most popular solution, for reasons of economy and speed, is some form of lightweight insulated metal cladding with cavity masonry work to the bottom 2m of the wall to provide security and impact resistance. The lightweight cladding would be carried on sheeting rails spanning between the columns of the portal frames.
Portal Frames can be defined as two dimensional rigid frames which have the basic characteristics of a rigid joint between column and beam.
The main objective of this form of design is to reduce bending moment in the beam which allows the frame to act as one structural unit.
The transfer of stresses from the beam to the column results in rotational movement at the foundation which can be overcome by the introduction of a pin/hinge joint.
For warehouses and industrial buildings, sloping roof made of purlins and ac sheet roofing between portals is provided. For assembly halls, portals with R.C slab roof cast monolithically is used.
Portal Frames are designed for the following loads:

  • roof load
  • wind load

While designing, care should be taken for proper

  • joints
  • foundation
  • bracing

If the joints at B, C, and D are not rigid, they will “open up” and the frame will be unstable when subjected to loads. This is the pack of cards effect. 1.Vertical loading results in A and E pushed outwards. If the foundation can’t resist horizontal push, outward movement will occur and the frame will lose strength. 2.Wind subjects the frame to uplift forces. Overturning forces on the sides & ends of the building. Drag forces on the roof and sides. 3.These destabilizing forces are resisted essentially by the weight of the building and in this regard, the foundations contribute significantly to this weight. The foundations are regarded as building’s anchors.
[You must be registered and logged in to see this image.]
CLICK HERE TO DOWNLOAD FULL WORKING DRAWING (.dwg)
Nội dung đã bị ẩn đi rồi, phải trả lời bài viết mới thấy được


Về Đầu Trang Go down
Xem lý lịch thành viên
 
TYPES OF PORTAL FRAMES (.dwg) (WORKING DRAWINGS)
Về Đầu Trang 
Trang 1 trong tổng số 1 trang

Permissions in this forum:Bạn không có quyền trả lời bài viết
0o -.......Forum 361dodesign.com.......- o0  :: AutoCad :: AutoCad :: Download file AutoCad-
Chuyển đến